中文
- 中文
- English
- français
- Deutsch
- русский
- italiano
- español
- português
- 日本語
- 한국의

100G QSFP28 DR1 1310nm LC SM 500M Transceiver

Features

Up to 106.25Gbps data rate by PAM4 modulation
1x100G PAM4 EML laser
Duplex LC receptacle optical interface
Single +3.3V power supply
DDM function implemented
Hot-pluggable QSFP28 form factor
Maximum link length of 500m on SMF fiber
Low power dissipation:<3.5W
International class 1 laser safety certified
Operating temperature range: 0℃ ~ +70 ℃
Compliant with ROHS6.0

Applications

100GBASE Ethernet Links
Switch & Router Connections
Data Centers

Standards

IEEE 802.3bm
IEEE 802.3cd
100G Lambda MSA
QSFP MSA
SFF-863

现在查询下载

类别

热门产品

产品详细信息

RQ-100G-DR1

100G QSFP28 DR1 1310nm LC SM 500M

100G QSFP28 DR1 1310nm LC SM 500M

The 100G QSFP28 DR1 Transceiver is designed to transmit and receive serial optical data links up to 106.25Gb/s data rate by PAM4 modulation format over single-mode fiber. It is a small-form-factor hot pluggable transceiver module integrated with the EML laser. It is compliant with100G Lambda MSA;QSFP MSA.

Document History

VER. & STATUS	DATE	DESCRIPTION OF CHANGE	Modifier
1.0	2021-12-10	Draft	XY

Specifications

(Tested under recommended operating conditions, unless otherwise noted)

Parameter	Symbol	Unit	Min	Typ	Max		Notes
Transmitter (per Lane)
Signaling Speed per Lane		GBd		53. 125± 100pm
Modulation format				PAM4
Center wavelength		nm	1304.5	1311	1317.5
Side-mode suppression Ratio	SMSR	dB	30
Optical output power	PAVG	dBm	-2.9		4
Outer Optical Modulation Amplitude	OMAouter	dBm	-0.8		4.2
Launch power in OMAouter minus TDECQ, each lane (min): for extinction ratio≥5 dB		dBm	-2.2
Launch power in OMAouter minus TDECQ, each lane (min): for extinction ratio < 5 dB		dBm	-1.9
Transmitter and dispersion penalty eye closure for PAM4	TDECQ	dB			3.4
Average Launch Power of Off Transmitter		dBm			-15
Optical Extinction Ratio	ER	dB	3.5
RIN17.1OMA		dB/Hz			-136
Optical Return Loss Tolerance	ORL	dB			15.5
Transmitter transition time (max)		ps			17
Transmitter reflectance		dB			-26
Receiver(per Lane)
Signaling Speed per Lane		GBd		53. 125± 100pm
Modulation format				PAM4
Input Operating Wavelength		nm	1304.5	1311	1317.5
Damage threshold		dBm	5
Average receive Power per Lane		dBm	-5.9		4
Receive Power (OMAouter)		dBm			4.2
Receiver reflectance (max)		dBm				-26
Stressed Receiver Sensitivity (OMAouter)		dBm				-1.9

Ordering Information

Part No.

Specifications

Application

Package

Data rate

Laser

Optical Power

Detector

Sensitivity

Temp

Reach

Others

RQ-100G-DR1

QSFP28

100G

EML

-2.9~4dBm

Max(-3.9,SEC Q-5.3)dBm

0~70 oC

500m

RoHS

100G Base Ethernet

Absolute Maximum Ratings

Parameter	Symbol	Unit	Min	Max
Storage Temperature Range	Ts	℃	-40	+85
Relative Humidity	RH	%	0	85
Power Supply Voltage	Vcc	V	-0.3	+3.6

Recommended Operating Conditions

Parameter	Symbol	Unit	Min	Typ	Max
Operating Case Temperature Range	Tc	oC	0	/	70
Power Supply Voltage	Vcc	V	3.135	3.3	3.465
Bit Rate(Per channel)	BR	Gbps		53.125

Optical Interface

Figure 1. Optical Interface

Note：Optical interface is duplex LC.

Principle diagram

Figure 2. Module Principle Diagram

Electric Ports Definition

Parameter	Symbol	Unit	Min	Typ		Max	Notes
Supply Voltage	VCC	V	3.14			3.47
Supply Current	ICC	mA				1100
Transmitter
Data Rate	BR	GBd		25.78125			NRZ
TX_DISABLE High	VDH	V	2			3.5	Input Voltage High
TX_DISABLE Low	VDL	V	-0.3			0.8	Input Voltage Low
TX_FAULT High [assert]	VFH	V	2			3.5	Output Voltage High
TX_FAULT Low [negated]	VFL	V	-0.3			0.8	Output Voltage Low
Receiver
Data Rate	BR	GBd			25.78125			NRZ
Differential Output Swing	VRXDIFF	mV	400			800		At TP4
Differential Eye Height	VEH	mV	228
Los-Output Voltage High	VOH	V	2			3.5		Output Voltage High
Loss-Output Voltage Low	VOL	V	-0.3			0.8		Output Voltage Low

Pin Description

No	Pin	Definition	Description	Note
1	1	GND	Ground	1
2	2	Tx2n	Transmitter Inverted Data Input
3	3	Tx2p	Transmitter Non-Inverted Data Input
4	4	GND	Ground	1
5	5	Tx4n	Transmitter Inverted Data Input
6	6	Tx4p	Transmitter Non-Inverted Data Input
7	7	GND	Ground	1
8	8	ModSelL	Module Select
9	9	ResetL	Module Reset
10	10	VccRx	+3.3V Power Supply Receiver	2
11	11	SCL	2-wire serial interface clock
12	12	SDA	2-wire serial interface data
13	13	GND	Ground	1
14	14	Rx3p	Receiver Non-Inverted Data Output
15	15	Rx3n	Receiver Inverted Data Output
16	16	Ground	Ground	1
17	17	Rx1p	Receiver Non-Inverted Data Output
18	18	Rx1n	Receiver Inverted Data Output
19	19	GND	Ground	1
20	20	GND	Ground	1
21	21	Rx2n	Receiver Non-Inverted Data Output
22	22	Rx2p	Receiver Inverted Data Output
23	23	Ground	Ground	1
24	24	Rx4n	Receiver Non-Inverted Data Output
25	25	Rx4p	Receiver Inverted Data Output
26	26	Ground	Ground	1
27	27	ModPrsL	Module Present
28	28	IntL	Interrupt
29	29	VccTx	+3.3V Power supply transmitter	2
30	30	Vcc1	+3.3v Power supply	2
31	31	LPMode	Low Power Mode
32	32	GND	Ground	1
33	33	Tx3p	Transmitter Non-Inverted Data Input
34	34	Tx3n	Transmitter Inverted Data Input
35	35	GND	Ground	1
36	36	Tx1p	Transmitter Non-Inverted Data Input
37	37	Tx1n	Transmitter Inverted Data Input
38	38	GND	Ground	1

Notes:

1. GND is the symbol for signal and supply (power) common for the QSFP28 module. All are common within the module and all module voltages are referenced to this potential unless otherwise noted. Connect these directly to the host board signal common ground plane.

2. VccRx, Vcc1 and VccTx are the receiving and transmission power suppliers and shall be applied concurrently. Recommended host board power supply filtering is shown in Figure 3 below. VccRx, Vcc1 and VccTx may be internally

connected within the module in any combination. The connector pins are each rated for a maximum current of 1000mA.

Figure 3. Electrical Pin-out Details

Module Memory Map

Figure 4 Digital Diagnostic Memory Map

Host Board Power Supply Filtering

Any voltage drop across a filter network on the host is counted against the host DC set

point accuracy specification. Inductors with DC Resistance of less than 0.1 Ohm should be used in order to maintain the required voltage at the Host Edge Card Connector. Figure is the suggested transceiver/host interface.

Figure 5 Recommended Host Board Power Supply Filtering

Package Outline

Figure 6 Package Outline

PCB layout recommendation

Figure 7 PCB Layout Recommendation

相关产品

100G QSFP28 SR4 100m 850nm MPO Optical Transceiver

100G QSFP28 SR4 100m 850nm MPO Optical Transceiver，support 100Gb/s and up to 100m transmission on MM fiber, it works in high-speed IDC connection solutions and so on. Features Compliant with IEEE Std 802.3bm Compliant with SFF-8665 Transmission data rate up to 25 .78125GbpsData rate per channel High Reliability 850nm VCSEL technology Electrically hot-pluggable Single +3 .3V power supply Case temperature range: 0 ~ +70℃ Maximum power consumption 2 .5W Single MPO12 connector RoHS complaint

100G QSFP28 CWDM4 2km LC Optical Transceiver

100G QSFP28 CWDM4 optical transceiver module, support 100Gb/s and up to 2 km transmission on SM fiber, it works in high-speed IDC connection solutions, and so on.

100G QSFP28 LR4 1310nm 10km LC Optical Transceiver

100G QSFP28 LR4 optical transceiver module, support 100Gb/s and up to 10 km transmission on SM fiber, it works in high-speed IDC connection solutions, and so on. Features 4 lanes MUX/DEMUX design Integrated LAN WDM TOSA / ROSA for up to 10 km reach over SMF Support 100GBASE-ER4 for line rate of 103.125Gbps and OTU4 for line rate of 111.81Gbps Aggregate bandwidth of >100Gbps Duplex LC connectors Compliant with IEEE 802.3-2012 Clause 88 standard IEEE 802.3bm CAUI-4 chip to module electrical standard ITU-T G.959.1-2012-02 standard· Single +3.3V power supply operating Built-in digital diagnostic functions Temperature range 0°C to 70°C RoHS Compliant Part Support FEC(Forward Error Correction)

100Gb QSFP28 ER4 40Km 1310nm LC Optical Transceiver

100G QSFP28 ER4 optical transceiver module, support 100Gb/s and up to 40 km transmission on SM fiber, it works in high-speed IDC connection solutions, and so on. Features: 4 lanes MUX/DEMUX design Support 100GBASE-ER4 for line rate of 103.125Gbps. Integrated LAN WDM TOSA / ROSA for up to 40 km reach over SMF. Aggregate bandwidth of >100Gbps Duplex LC connectors Compliant withIEEE 802.3-2012 Clause 88 standard IEEE 802.3bm CAUI-4 chip to module electrical standard ITU-T G.959.1-2012-02 standard· Single +3.3V power supply operating Built-in digital diagnostic functions Temperature range 0°C to 70°C RoHS Compliant Part Support FEC(Forward Error Correction)

100Gb QSFP28 ZR4 80Km 1310nm LC Optical Transceiver

100G QSFP28 ZR4 optical transceiver module, support 100Gb/s and up to 80 km transmission on SM fiber, it works in high-speed IDC connection solutions, and so on. Features 4 lanes MUX/DEMUX design Support 100GBASE-ZR4 for line rate of 103.125Gbps and OTU4 for line rate of 111.81GbpsLANWDM EML laser and PIN receiver with SOA Aggregate bandwidth of >100Gbps Duplex LC connectors Compliant withIEEE 802.3-2012 Clause 88 standard IEEE 802.3bm CAUI-4 chip to module electrical standard ITU-T G.959.1-2012-02 standard· Single +3.3V power supply operating Built-in digital diagnostic functions Temperature range 0°C to 70°C RoHS Compliant Part Support FEC(Forward Error Correction)

100Gb/s QSFP28 DWDM Dual CS Adaptor Transceiver

100G QSFP28 DWDM optical transceiver module, support 48*100Gb/s DWDM System and up to 80 km transmission on SM fiber, it works in high-speed IDC connection solutions.

100GBASE-SR Bi-Directional QSFP28 850/900nm 100m DOM LC MMF Optical Transceiver Module

100G QSFP28 BIDI optical transceiver module is a pluggable optical transceiver with a duplex LC connector interface for short-reach data communication and interconnect applications using Multi-Mode Fiber (MMF). It offers customers a compelling solution that enables reuse of their existing 10 Gb duplex MMF infrastructure for migration to 100 Gigabit Ethernet connectivity.

100GBASE-LR Bi-Directional QSFP28 1280/1310nm 20km LC SM Optical Transceiver Module

100G QSFP28 BIDI optical transceiver module is a pluggable optical transceiver with a Simplex LC connector interface for long-reach data communication and interconnect applications using one core Single-Mode Fiber (SMF).

联系我们